You’ve turned the taps off, the shower’s done, and yet the shower head keeps on dripping. One drop, then another, landing on the shower floor long after you’ve walked away. It’s the kind of small, steady leak that’s easy to live with for a day or two, but it gets on your nerves fast, and it doesn’t feel big enough to justify calling a plumber out.
The good news is that most of the time, you don’t need to.
A leaking shower is usually something you can fix yourself with a few basic tools and a quick trip to the hardware store. The key is knowing which part to replace, because without that, you can easily spend an afternoon on the wrong fix while the drip carries on.
So the first step is tracing the leak back to where it starts. Once you know which part has worn, the fix itself is usually straightforward, and you’ll have the bathroom quiet again before the day’s out.
TL;DR
- Stop the water first if you need to. If a tap won’t shut off, or water is coming through the wall, close the main stopcock at the water meter. Fill a few bottles first. Closing the shower taps only stops the flow at the head.
- Some dripping is normal. A few drips that stop within a minute or two are water draining from the head and arm. A drip that carries on means a worn part inside the tap.
- Find the leak by where the water appears. Run the shower for a minute, then check each joint with a dry cloth. Start at the head, then the hose, then the wall plate.
- A small worn part is often a DIY fix. You can replace the washer and plumber’s tape at the head joint, the shower head itself, or a tap washer or jumper valve.
- Some repairs need a licensed plumber. That covers shower hoses, hose washers, a worn tap seat, ceramic cartridges and mixers.
- Call a plumber ASAP for water in the wall. Signs include water behind the wall plate, an arm that moves, bubbling paint, swollen skirting boards or a ceiling stain below. Keep the shower off until help arrives.
Find What’s Causing Your Shower Head to Leak
Where the water appears tells you which part has worn. So, run the shower for about a minute, then turn it off, and then check each connection in order with a dry cloth or paper towel.
What to look for while the shower runs
Keep the water running and check these three spots in order:
- Where the head meets the arm. Water dribbling or spraying here usually means a loose connection, a worn or missing rubber washer inside the head, or a worn thread seal. Don’t try over-tightening it as a way to fix the leak, as it can crack the head or damage the arm.
- Along the shower hose. Water at either end usually comes from a worn hose washer or a loose hose nut. But if the water is leaking from the middle, it means the hose has split and needs replacing.
- Where the arm enters the wall. Water running from behind the round wall plate, or an arm that moves when touched, suggests the fitting inside the wall is loose, corroded or has a worn seal. And you can’t fix that by twisting or pushing the arm to tighten it as it could crack the fitting behind the wall. This repair needs a QBCC-licensed plumber.
What to look for when turning the taps off
Check that the taps close properly. If the handle turns fully while water keeps running, or spins freely without shutting off, it means the internal shut-off part, often a worn spindle or cracked ceramic cartridge, has broken.
At this point, your shower taps can no longer control the water, so use the main stopcock at the water meter to shut off the supply. In Townsville, water meters are usually near the front boundary of the property, often close to the left or right corner.
Important: Closing the main stopcock cuts water to the whole house, so fill a few bottles or the kettle first if you need drinking water.
What to look for after the shower is off
Once the water is off, keep watching the shower head for a few minutes. A few drips that stop within a minute or two are just water draining out of the head and arm. That is normal.
But if that drip carries on or returns later, that tells you the water is getting past a worn part inside the tap, even with the handle fully closed.
A slow drip like this can usually wait for a daytime fix, though it does waste water. You may be wondering if you can fix it yourself. The answer depends on your tap type. Turn the handle off and notice how far it goes.
A full turn or more means a rubber washer, which you can swap yourself. A quarter or half turn, or a single lever, means a ceramic cartridge. That needs a plumber. We have covered both in detail for you in the fix section below.
Fix Your Leaking Shower Head Based on the Cause Identified
If you have already found where the leak is coming from, you can go straight to the fix for that part. But before you start, cut the water supply.
For work on the shower head, you can do that by simply closing the shower taps firmly by hand. And if you need to take a tap apart, shut off the water to the whole house first using the main stopcock at the water meter, and leave it off until the tap is back together.
Fix a leak where the head meets the arm
The shower arm is the pipe that sticks out of the wall. Your shower head screws onto the end of it. Inside the nut at the base of the head sits a small rubber washer, which presses against the arm to seal the joint.
The thread on the arm is also wrapped in plumber’s tape, which fills the gaps between the threads. Both parts wear out over time. When either one goes, water dribbles or sprays from the joint.
To fix it:
- Unscrew the shower head.
- Take out the old washer and fit a new one.
- Wrap fresh plumber’s tape clockwise around the arm thread.
- Screw the head back on by hand. Don’t use the wrench, as over-tightening can crack it.
Some shower heads have a small water-saving disc at this joint, and if that disc is crooked, it can cause the same leak. So seat it flat, and the leak will stop.
If the head itself is cracked or worn out, then you’ll need to replace it. QBCC lists replacing a shower head as unregulated work, so you can do it yourself.
Fix a leak from the shower hose
Start with the nut at each end of the hose. Make sure both are hand-tight. If water still leaks at either end, that tells you the rubber washer inside has worn.
And if you see water along the length of the hose, it means it has split, and the whole hose needs replacing.
Unlike replacing shower heads, QBCC doesn’t list this as unregulated work; that means you need a plumber for it. At Emergency Plumbers Townsville, we’re available 24/7 for call-outs. Ring us anytime to have your leaking hose fixed, and we’ll aim to reach you in under 30 minutes.
Fix a constant drip from the shower head
A constant drip from the shower head comes from the tap. Every tap has a seal inside that stops the water when you turn it off, and once that seal wears, water slips past and drips out through the shower head.
Showers have one of two types of tap, and each uses a different seal. Turn the handle off and notice how far it goes:
- A handle that takes a full turn or more has a rubber washer as its seal.
- A handle that closes in a quarter or half turn, or a single-lever mixer, has a ceramic cartridge as its seal.
Full-turn taps: sealed by a rubber washer
Start by finding which tap is leaking. Feel the water as it drips – if it’s warm, that points to the hot tap, and cold water points to the cold tap. Don’t rely on which side the tap is on.
QBCC lists replacing a tap washer or jumper valve as unregulated work, so you can do this yourself. Here’s how:
- Turn the water off at the main stopcock.
- Take off the handle and cover.
- Unscrew the spindle.
- Swap the old washer for a matching new one.
- Put everything back together.
If it still drips after a new washer, the tap seat has probably worn – that is the surface the washer presses against. A plumber will have to fix it by grinding the seat back to a smooth, level surface.
Quarter-turn taps and mixers: ceramic cartridge
Inside these taps sit a cartridge, a small cylinder holding two ceramic discs. With the tap shut, the discs press flat against each other and block the water. If a disc wears or cracks, water slips through the gap, even with the handle closed.
The fix is a new cartridge matched to your tap, since each brand makes its own to fit its taps. On older mixers, the right cartridge can be hard to track down, and once it’s no longer made, replacing the whole mixer is often the only option left.
Either job needs a licensed plumber, and our team at Emergency Plumbers Townsville can handle it for you any time, day or night. Call us now.
Call a Plumber ASAP If You’ve Found Water Behind the Wall
Your shower arm connects to a fitting inside the wall. If that fitting or the pipe behind it starts leaking, the water runs into the wall cavity instead of staying in the shower. Because the water spreads out of sight, the first signs of the leak often show up on the other side of the wall, or in the room below.
Check for these:
- Damp or bubbling paint on the other side of the wall
- Swollen skirting boards
- A stain on the ceiling below, in a high-set or two-storey home
Any of these means water has probably been behind the wall for a while. And Townsville’s warm, humid weather makes that a bigger concern. That water soaks into the timber frame and wall lining, and if left too long, mould can develop.
That is why this leak needs fixing quickly. It isn’t a DIY job, so leave the wall alone and call a licensed plumber. And until they arrive, turn off the water at the main stopcock. That stops more water reaching the wall and avoids using the shower too.
Wet walls don’t keep office hours, and neither do we. Emergency Plumbers Townsville is available 24/7. We’re licensed and insured, and we aim to reach most Townsville suburbs in under 30 minutes.
FAQs
Can I keep using the shower until the plumber arrives?
If it’s a small drip from the shower head or tap, you can usually keep using the shower.
If water is leaking inside the wall, or a tap won’t shut off, leave the shower, and turn the water off at the main stopcock and keep it off until the plumber arrives.
How much does an after-hours visit cost?
After-hours rates depend on the time of the call and the job. Call us and we will confirm the call-out cost before a plumber heads out. Most shower head and washer jobs are quick. Any parts you need, like a new washer or cartridge, are added to the bill.
Will insurance cover water damage from a leaking shower?
Sometimes. A flat yes or no would be wrong. Many policies cover a sudden or accidental escape of water. Many exclude a slow leak or wear and tear, and some exclude a leaking shower base or recess.
A dripping shower is usually a slow leak, so check the escape of liquid section of your Product Disclosure Statement (PDS) before you claim. We can give you a plumbing report on request, to send to your insurer.
Do you service my area?
We cover all of Townsville’s suburbs, along with towns up to 200 km away by road. If you’re outside the city, give us a call, and we’ll let you know how soon we can get a plumber out to look at your shower.