You’ve spotted water around the base of your hot water system, a dripping pipe, or a wet patch nearby, and you’re right to look into it. The good news is that not every leak means trouble. Sometimes a small amount of water is just your system working the way it’s meant to.
Other times, it’s a sign of a failing tank, a loose fitting or a faulty valve that will only get worse if it’s left. This guide will help you work out which one you’re dealing with, what to check, and how urgent it really is, so you know whether to ring a plumber straight away or whether it can wait until Monday.
TL;DR
- Make it safe first. Switch off the power or gas, then close the cold water isolation valve. If it won’t shut, close the water meter at the front of your property.
- Closing hot taps inside the house won’t stop the tank refilling. Only the isolation valve or the meter will.
- Some water is normal. A small drip from the relief valve pipe while the tank heats is expected. So are damp cold pipes and a heat pump’s condensate drain.
- Watch for signs of a real fault. Constant dripping, a steady stream, steam or very hot water from the relief valve pipe needs a plumber. Never cap or block that pipe.
- Fittings and valves can differ. A slow drip from a fitting or valve can wait for a booked repair. Water spraying from a connection needs a same-day call.
- Call a plumber now for these. Water seeping from the tank body, water coming through the ceiling from a roof tank, or water near electrical or gas parts. A leaking tank generally can’t be patched.
First of All, Stop the Leak and Make It Safe
If your hot water system is leaking, the biggest risk is water near electrical parts. Work through these steps in order. Each one takes a minute or two.
- Switch off the power or gas. For electric, solar boost and heat pump systems, turn off the hot water circuit at the switchboard. For gas, turn the gas control on the unit to off. If the switchboard is wet, or you’d have to stand in water to reach it, stay back and call an electrician.
- Close the cold water isolation valve. It’s on the cold pipe running into the tank, close to the unit. It usually has a small lever or a tap-style handle. Turn a tap-style handle clockwise until it stops. For a lever, turn it so it sits across the pipe. If it feels stuck, don’t force it. Move on to the meter instead.
- Use the water meter if that valve won’t shut. An isolation valve that hasn’t been touched for years can seize with build-up, and forcing it can snap it, so don’t strain against it. If it won’t turn easily, cut the supply at the meter instead. You’ll usually find the meter towards the front of the property, near the left or right corner. Look for a small lid set into the ground, often in the lawn or garden bed. Lift it and you’ll see the meter with a valve beside it. Close it the same way as the isolation valve. This turns off water to the whole house. If you can’t find it, Townsville Water can help on 13 48 10.
- Move belongings and contain the water. Shift rugs, boxes and electronics out of the wet area. Use buckets and towels to catch drips and mop up pooled water, and keep kids and pets away, because leaking water can be very hot.
- Note details for your plumber. Take a photo of the compliance plate on the tank. It shows the brand, model, and age. Also check exactly where the water is coming from, such as a pipe connection, a valve, the base, or the tank body. This shortens the diagnosis and lets the plumber arrive with the right parts.
Important to note, turning off the hot taps inside the house is a common mistake. It does nothing to stop the tank refilling. The isolation valve is the one that counts.
Once the system is isolated, you’ve bought yourself some time. Now, finding the source of the leak will help you decide how urgently you need the plumber to come.
Find the Source of the Leak
Where the water appears and how often it happens will tell you what you’re dealing with. Then you can decide whether to book a repair for later, or call a plumber right away.
Water Dripping From the Relief Valve Overflow Pipe
Look for a pipe near the top or side of the hot water tank and ending a short way above the ground. If water drips from the end of it, that’s your relief valve (also called the TPR valve) releasing water.
In many cases, this is normal. As the water in the tank heats up, it expands, and the TPR valve lets a little out to keep the pressure at a safe level. If your system has an expansion control valve (ECV) on the cold-water inlet, you may see that valve releasing the water instead.
What matters is how much is coming out and for how long.
What you can do yourself
Watch the pipe while the tank is heating. A small drip that stops once heating has finished is normal, and as a guide, discharge of roughly 1/50 of the hot water used is within the expected range.
If it keeps dripping after heating has stopped, and your manufacturer’s manual allows it, gently lift the TPR valve’s easing lever for a few seconds, then lower it slowly. This can sometimes clear minor debris from the valve seat. Stand clear of the drain outlet, as the water may be hot enough to burn you, and never force the lever or let it snap shut.
When to call a plumber
If the dripping still doesn’t stop, book a plumber. The cause is usually a worn valve, debris that won’t clear, supply pressure that’s too high, or a faulty thermostat letting the water overheat. They may replace the TPR valve, check the thermostat and temperature settings, inspect the ECV if you have one, or test your water pressure. Under AS/NZS 3500.1, static pressure at outlets inside a building should not exceed 500 kPa, so if yours is higher, they may install or adjust a pressure-limiting valve.
Don’t wait if you see a constant stream of very hot water, steam, or water escaping quickly. Call a plumber straight away.
Our team at Emergency Plumbers Townsville is on call 24/7 for exactly these situations, and we’ll have a plumber at your place in under 30 minutes, day or night.
Condensation and Heat Pump Drainage
Water on cold pipes, around the unit, or in the tray and on the ground below can look alarming. Usually it’s condensation, and that’s normal.
Townsville’s humid, tropical climate can make condensation more noticeable, so it’s easy to mistake for a leak. Heat pumps also produce condensate as part of normal operation, and it drains continuously through a condensate line. Water from that line, or dripping from cold pipes, is expected.
If the water only ever shows up on cold pipes or the condensate line, you can relax.
What you can do yourself
Dry the area, then watch where the water reappears. If it follows humid weather or the heating cycle and comes from the condensate line, it’s likely normal. You don’t need to do anything.
When to call a plumber
If the water is coming from the tank, a fitting or a valve, you’re dealing with a leak. Work through the other causes in this section to find the one that matches, and each one tells you when to ring a plumber.
Water at the Base or Pooling Under the Tank
If you notice a puddle under the tank, damp flooring, rust stains, or moisture low down on the tank, the water could be coming from the drain valve, a fitting or pipe connection, or the tank itself.
Start by checking the drain valve. On systems that have it, it sits near the base. If it’s been left slightly open or its washer has worn, water can seep out and look a lot like a leaking tank.
The other, more serious possibility is the tank. Most storage tanks have a sacrificial anode, a metal rod that corrodes so the tank doesn’t. Once the anode wears out, the tank takes the damage instead, and over time the inner cylinder can rust through. Water seeping from the tank body, rust staining, or pooling with no valve or fitting nearby usually points to this.
What you can do yourself
Check that the drain valve is fully closed. Then have a look over the tank and pipework to see where the water seems to come from, without touching any electrical parts.
When to call a plumber
If the drain valve is fully closed and water still seeps from it or from a fitting, book a plumber, because a slow, contained seep like that is a repair job. They’ll first confirm whether the water is coming from the valve or the tank wall.
A faulty drain valve can be replaced, whereas a leaking cylinder generally can’t be patched, so replacement is usually the only option in that case.
It’s only an emergency call-out if water is actively leaking, spreading from the tank body, pooling across a wet floor, or if it’s near electrical components. And while you wait for a plumber to arrive, isolate the system as described earlier if it’s safe, and don’t open the tank or remove any valves.
Water Leaking From the Top of the Tank
If water is appearing at the top of the system, it usually comes from the cold inlet or hot outlet connections, the isolation valve, or the TPR valve thread. On outdoor units, Townsville’s coastal salt air can corrode brass fittings and threaded joints faster than in inland areas.
Whether the water is dripping slowly or spraying decides how quickly it needs attention.
What you can do yourself
Have a look at how the water is leaving the connection. If it’s spraying, it won’t stop until the system is isolated, so close the cold water isolation valve as described earlier, as long as it’s safe to reach. Whatever you see, avoid tightening a leaking threaded connection hard, because that can damage the fitting or the tank thread.
When to call a plumber
A slow drip from one of these connections isn’t an emergency, so you can ring a plumber and book a visit at a time that suits you. They’ll find which connection is leaking, then reseal or replace it and check whether corrosion has spread to the nearby pipework.
If the water is spraying, ring a plumber straight away. Even after you’ve closed the isolation valve, the fitting still needs repairing before you can turn the water back on, and the longer it’s leaking, the more water damage it can cause.
Water Coming Through the Ceiling (Solar Systems)
If you have a close-coupled solar system, where the tank sits on the roof, a leak can show up as ceiling stains or water running down the roof. The cause could be anything from a worn fitting to damaged flashing around the tank, and it’s not something you can check safely from the ground, so leave the diagnosis to a plumber.
Where the water is showing up tells you how quickly you need one.
What you can do yourself
Check from inside the house and from the ground. Look at the ceiling for stains, and at any light fittings for drips. From the ground, see whether water is running down the roof or coming off the sheeting near the tank. If it only appears while the tank is heating, it’s likely the normal relief valve discharge.
Please don’t climb onto the roof to look closer in any case. And if water is near a light fitting, switch off the power at the switchboard if it’s safe to do so, then keep clear of that area.
When to call a plumber
If the water isn’t normal relief valve discharge, or is coming through the ceiling, book a same-day plumber visit. They can isolate the tank, repair the fitting or connection, and check the roof penetration and flashings during the same visit.
Water From a Gas Hot Water System
Water around a gas hot water system can come from the water pipework, the tank, a valve, or the gas booster itself. It tends to show up around the base of the unit, flue, gas connection, burner area or tank.
Because gas is involved, it’s best to treat any leak with caution until a licensed professional has checked it.
What you can do yourself
While you wait for help, turn off the gas isolation valve, but only if it’s safe to reach. Stay back from the unit, and don’t try to relight the pilot or repair the booster yourself.
When to call a plumber
If the water is clearly away from the gas parts, a minor leak can wait to book a plumber within a day or two. Meanwhile, turn off the water supply to the unit if the leak is steady. A licensed gasfitter will isolate the gas supply, diagnose the booster or connection fault, and repair or replace the affected component.
Important: call for urgent help if you notice a hissing sound, an unusual flame, smoke, or water near gas fittings. And if you smell gas, leave the area and avoid electrical switches and open flames, then call 000 or your gas supplier’s emergency line.
24/7 Emergency Hot Water Repairs in Townsville
A leak can have several causes, and how you deal with it depends on getting the diagnosis right. A seeping drain valve can look like a failing tank, and normal relief valve discharge can look like a fault. When the cause is identified correctly the first time, you avoid paying for a replacement you didn’t need, a second call-out, or water damage from a leak that was never properly fixed.
That’s where our team at Emergency Plumbers Townsville comes in. We hold a QBCC licence and work on electric, gas, solar and heat pump hot water systems, so one call is enough to find the cause and fix it.
If water is spreading, dripping indoors, discharging hot water, or sitting near electrical or gas parts, switch off the water and power or gas first and make it safe. Then ring us for 24/7 emergency hot water repairs in Townsville. We’ll come out as soon as we can, track the cause, and make the system safe for you.
FAQs
Can I still use hot water while it’s leaking?
No, because every time you use hot water, the tank refills from the mains, which can keep the leak running and worsen water damage. Turn off the cold-water isolation valve and power or gas supply if safe, then call a licensed plumber.
You can usually continue using hot water only if the water is normal condensation, heat pump condensate, or a brief relief valve discharge during heating that stops afterwards.
How fast can a plumber get to me?
We aim to attend urgent Townsville call-outs within 30 minutes, with longer travel times for properties outside Townsville. Availability and response time can vary with traffic, weather, call volume, and your exact location.
Is a leaking hot water system covered by warranty?
It depends on the cause, the system’s age, and the manufacturer’s warranty terms. Tank or cylinder warranties may cover manufacturing or cylinder faults, but exclusions can apply for corrosion, incorrect installation, excessive water pressure, unsuitable water supply, or inadequate maintenance.
Check the compliance plate on the unit and your original installation or warranty paperwork, then ask the manufacturer or a licensed plumber to confirm whether the fault is covered.
Do you come out to my area after hours?
Yes. We provide 24/7 emergency hot water repairs across Townsville suburbs and towns within 200 km by road. Call anytime for urgent assistance, including nights, weekends, and public holidays.
When should I call instead of waiting?
Call a licensed plumber now if water is spreading, dripping indoors, discharging hot water or steam, or sitting near electrical or gas components. A brief TPR valve drip during heating that stops afterwards is usually normal; constant dripping, a steady stream, or very hot discharge needs prompt attention.